How to Measure a Box for Custom Packaging
Give us the measurements in Length x Width x Depth/Height inside of the box. Also mention that the measurements are of the product or inside of your existing box. It will help us prepare the right template.
Length, width and depth mean specific things
- Length is the longer of the two dimensions on the opening face and it runs left to right.
- Width is the shorter dimension on that same face and it runs front to back.
- Depth is the third dimension and it runs from the opening down to the base.
Packaging always lists these in that order so 200 x 150 x 80 mm means 200 long, 150 wide and 80 deep. Writing the same three numbers in a different order changes the box completely and it is the fastest way to end up with a dieline you cannot use.
Always give internal dimensions
Internal dimensions are the space your product actually sits in. External dimensions include the board itself and on corrugated that difference is large enough to stop a product going in at all.
| Material | Wall thickness | Added to each outside dimension |
|---|---|---|
| 300 to 350 GSM SBS carton | about 0.4 mm | about 0.8 mm |
| 350 to 400 GSM SBS carton | about 0.5 mm | about 1 mm |
| E flute corrugated | about 1.5 mm | about 3 mm |
| B flute corrugated | about 3 mm | about 6 mm |
| Rigid box, wrapped greyboard | about 2 to 2.5 mm | about 4 to 5 mm |
So a 200 x 150 x 80 mm internal carton in 350 GSM board measures roughly 201 x 151 x 81 mm on the outside. The same internal size in B flute corrugated measures roughly 206 x 156 x 86 mm. Tell us which figure you are giving us if there is any doubt and we will confirm it on the dieline.
Measure the product, not the old box
An existing box already carries someone else’s clearance and someone else’s board. Measure the product itself and let us add the allowance.
- Lay the product the way it will sit in the box and measure the longest side. That is your length.
- Measure front to back for the width, then top to bottom for the depth.
- For anything round, measure straight across the widest point rather than around the curve.
- Measure bottles and jars with the cap or the pump in place, and measure a pump in its locked down position.
- Include the insert, the tissue or the sleeve if the product ships with one.
Then add clearance so the product goes in without being forced. These are the clearance allowances our dielines are built to.
- Most products: add 3 to 4 mm on each internal dimension
- Hard edged items like a soap bar: add 2 to 3 mm, because too much room lets the item rub the print
- Bottles and jars: widest diameter plus 3 mm, and assembled height plus 3 mm
- Filled pouches: measure a pouch that has been handled rather than one straight off the filling line
Worked examples
| Product | Product measured | Internal box size |
|---|---|---|
| Soap bar | 85 x 60 x 22 mm | 89 x 64 x 25 mm |
| 8 oz candle jar | 86 mm across, 100 mm tall | 90 x 90 x 105 mm |
| 30 ml dropper bottle | 35 mm across, 112 mm with the cap | 40 x 40 x 118 mm |
| Tray of 12 chocolates | 130 x 100 x 25 mm | 135 x 105 x 30 mm |
| 100 ml lotion pump | 48 mm across, 155 mm pump down | 53 x 53 x 158 mm |
Six mistakes that cost a reprint
- Sending external dimensions when the quote needs internal ones.
- Measuring an old box and passing on its clearance and its board thickness.
- Listing the three numbers in an order other than length by width by depth.
- Mixing millimeters and inches inside one specification.
- Measuring a pump bottle with the pump up rather than locked down.
- Forgetting the insert, so the product fits but the finished pack does not close.
Make sure to keep the measurement unit consistent for all three sides. For example: write 200 × 150 × 80 mm. One inch is 25.4 mm, so pick one unit and stay with it.
Share your product size and we will share a dieline
Give us the internal dimensions, the quantity you need and the date the boxes have to be in your hands. You get a free dieline and a 3D mockup back. A plain structural sample takes 3 to 5 working days and a printed sample takes 7 to 10. Post us the product if the fit is unusual and we will measure it ourselves before we cut anything.
Sales@boxesexpert.com · Copper Dr, Newport, DE 19804, USA · 8am to 5pm EST on weekdays
