How to Measure a Box for Custom Packaging

Give us the measurements in Length x Width x Depth/Height inside of the box. Also mention that the measurements are of the product or inside of your existing box. It will help us prepare the right template.

Length, width and depth mean specific things

Length Depth Width Front panel
  • Length is the longer of the two dimensions on the opening face and it runs left to right.
  • Width is the shorter dimension on that same face and it runs front to back.
  • Depth is the third dimension and it runs from the opening down to the base.

Packaging always lists these in that order so 200 x 150 x 80 mm means 200 long, 150 wide and 80 deep. Writing the same three numbers in a different order changes the box completely and it is the fastest way to end up with a dieline you cannot use.

Always give internal dimensions

Internal dimensions are the space your product actually sits in. External dimensions include the board itself and on corrugated that difference is large enough to stop a product going in at all.

How much each material adds to the outside of a box
MaterialWall thicknessAdded to each outside dimension
300 to 350 GSM SBS cartonabout 0.4 mmabout 0.8 mm
350 to 400 GSM SBS cartonabout 0.5 mmabout 1 mm
E flute corrugatedabout 1.5 mmabout 3 mm
B flute corrugatedabout 3 mmabout 6 mm
Rigid box, wrapped greyboardabout 2 to 2.5 mmabout 4 to 5 mm

So a 200 x 150 x 80 mm internal carton in 350 GSM board measures roughly 201 x 151 x 81 mm on the outside. The same internal size in B flute corrugated measures roughly 206 x 156 x 86 mm. Tell us which figure you are giving us if there is any doubt and we will confirm it on the dieline.

Measure the product, not the old box

An existing box already carries someone else’s clearance and someone else’s board. Measure the product itself and let us add the allowance.

  1. Lay the product the way it will sit in the box and measure the longest side. That is your length.
  2. Measure front to back for the width, then top to bottom for the depth.
  3. For anything round, measure straight across the widest point rather than around the curve.
  4. Measure bottles and jars with the cap or the pump in place, and measure a pump in its locked down position.
  5. Include the insert, the tissue or the sleeve if the product ships with one.

Then add clearance so the product goes in without being forced. These are the clearance allowances our dielines are built to.

  • Most products: add 3 to 4 mm on each internal dimension
  • Hard edged items like a soap bar: add 2 to 3 mm, because too much room lets the item rub the print
  • Bottles and jars: widest diameter plus 3 mm, and assembled height plus 3 mm
  • Filled pouches: measure a pouch that has been handled rather than one straight off the filling line

Worked examples

Worked examples, product size to internal box size
ProductProduct measuredInternal box size
Soap bar85 x 60 x 22 mm89 x 64 x 25 mm
8 oz candle jar86 mm across, 100 mm tall90 x 90 x 105 mm
30 ml dropper bottle35 mm across, 112 mm with the cap40 x 40 x 118 mm
Tray of 12 chocolates130 x 100 x 25 mm135 x 105 x 30 mm
100 ml lotion pump48 mm across, 155 mm pump down53 x 53 x 158 mm

Six mistakes that cost a reprint

  1. Sending external dimensions when the quote needs internal ones.
  2. Measuring an old box and passing on its clearance and its board thickness.
  3. Listing the three numbers in an order other than length by width by depth.
  4. Mixing millimeters and inches inside one specification.
  5. Measuring a pump bottle with the pump up rather than locked down.
  6. Forgetting the insert, so the product fits but the finished pack does not close.

Make sure to keep the measurement unit consistent for all three sides. For example: write 200 × 150 × 80 mm. One inch is 25.4 mm, so pick one unit and stay with it.

Share your product size and we will share a dieline

Give us the internal dimensions, the quantity you need and the date the boxes have to be in your hands. You get a free dieline and a 3D mockup back. A plain structural sample takes 3 to 5 working days and a printed sample takes 7 to 10. Post us the product if the fit is unusual and we will measure it ourselves before we cut anything.

Sales@boxesexpert.com · Copper Dr, Newport, DE 19804, USA · 8am to 5pm EST on weekdays